Datasets:

librarian-bots

/

arxiv-metadata-snapshot

like 5

Follow

Librarian Bots 75

physics/0111032

Eric J. Siskind

M. J. Browne, A. E. Gromme, E. J. Siskind

Front End CAMAC Controller for SLAC Control System

Poster Paper for ICALEPCS-2001 (WEAP022), 3 pages, pdf

eConf C011127 (2001) WEAP022

physics.ins-det

Most of the devices in the SLAC control system are accessed via interface modules in ~450 CAMAC crates. Low-cost controllers in these crates communicate via a SLAC-proprietary bit-serial protocol with 77 satellite control computers ("micros") within the accelerator complex. A proposed upgrade replaces the existing Multibus-I implementation of the micro hardware with commercial-off-the-shelf ("COTS") personal computers. For increased reliability and ease of maintenance, these micros will move from their current electrically noisy and environmentally challenging sites to the control center's computer room, with only a stand-alone portion of each micro's CAMAC interface remaining in the micro's original location. This paper describes the hardware/software architecture of that intelligent front-end CAMAC controller and the accompanying fiber optic link board that connects it to the PC-based micro's PCI bus. Emphasis is placed on the hardware/software techniques employed to minimize real-time latency for pulse-to-pulse operations that control accelerator timing, acquire data for fast feedback loops, and change device settings to close those loops. The controller provides the sole interface between the COTS computing/networking environment and the existing CAMAC plant. It also supports higher bandwidth commercial byte-serial crate controllers and legacy BITBUS hardware.

physics/0111034

Gianluca Chiozzi

G. Chiozzi (1), B. Gustafsson (1), B. Jeram (1), P.Sivera (1), M. Plesko (2), M. Sekoranja (2), G. Tkacik (2), J. Dovc (2), M. Kadunc (2), G. Milcinski (2), I.Verstovsek (2), K. Zagar (2) ((1)ESO Garching bei Muenchen DE, (2)JSI, Ljubljana, SI)

Common Software for the ALMA project

ICALEPCS 2001 Conference, San Jose, CA, 27-30 November 2001, Paper THAT005, 3 pages, 2 embedded figures

eConf C011127 (2001) THAT005

physics.acc-ph physics.ins-det

The Atacama Large Millimeter Array (ALMA) is a joint project between astronomical organizations in Europe, USA and Japan. ALMA will consist of at least 64 12-meter antennas operating in the millimeter and sub-millimeter wavelength range, with baselines up to 10 km. It will be located at an altitude above 5000m in the Chilean Atacama desert[1]. The ALMA Common Software (ACS) provides a software infrastructure common to all partners and consists of a documented collection of common patterns in control systems and of components, which implement those patterns. The heart of ACS is an object model of controlled devices, called Distributed Objects (DOs), implemented as CORBA network objects. Components such as antenna mount, power supply, etc. are defined by means of DOs. A code generator creates Java Bean components for each DO. Programmers can write Java client applications by connecting those Beans with data-manipulation and visualization Beans using commercial visual development tools or programmatically. ACS is based on the experience accumulated with similar projects in the astronomical and particle accelerator contexts, reusing and extending concepts and components. Although designed for ALMA, ACS has the potential for being used in other new control systems and other distributed software projects, since it implements proven design patterns using state of the art, stable and reliable technology.

physics/0111035

M. K. Samal

Manoj K. Samal

Speculations on a Unified Theory of Matter and Mind

To appear in proceedings of the International Conference "Science and Metaphysics: A Discussion on Consciousness and Genetics" at NIAS, IISc. Campus, Bangalore, India, (June 2001)

physics.gen-ph

Physics is so successful today in understanding the nature of matter. What can it say about mind ? Is it possible to have a unified theory of matter and mind within the framework of modern science ? Is Consciousness an accident or is it a natural consequence of laws of nature ? Are these laws of nature the same as the laws of physics ? We make an attempt here to unify mind with matter based on an extended formalism borrowed from Quantum theory where information plays a more fundamental role than matter or thought.

physics/0111036

Michael Shaw

M. J. Shaw, R. A. Sacks, C. A. Haynam, and W. H. Williams

Computational Modeling in Support of the National Ignition Facilty Operations

3 pages, submission to ICALEPCS 2001 conference

eConf C011127 (2001) WEAP063

PSN # WEAP063

physics.optics

Numerical simulation of the National Ignition Facility (NIF) laser performance and automated control of the laser setup process are crucial to the project's success. These functions will be performed by two closely coupled computer code: the virtual beamline (VBL) and the laser performance operations model (LPOM).

physics/0111037

Andrew Johnson

A. N. Johnson and M. R. Kraimer (Advanced Photon Source, Argonne National Laboratory)

Reimplementing the EPICS Static Database Access Library

Poster paper (THAP016) at ICALEPCS 2001, San Jose CA, November 2001. 3 pages, PDF

eConf C011127 (2001) THAP016

physics.ins-det

The Static Database Access library was first introduced in EPICS (Experimental Physics and Industrial Control System) Release 3.11 in 1994. It provides an application program interface (API) for database configuration tools written in C to manipulate database record definitions and is used for various tasks within the core EPICS software. This paper describes the structure of a replacement for the original library that adds a native C++ API and will make some future enhancements to EPICS significantly easier to implement.

physics/0111040

Kenneth Evans Jr.

Kenneth Evans Jr

EPICS for PDAs

eConf C011127 (2001) THAP009

physics.acc-ph physics.ins-det

With the advent of readily available wireless communications and small hand-held computers, commonly known as personal digital assistants (PDAs), it is interesting to consider using these portable devices to access a control system. We have successfully ported the Experimental Physics and Industrial Control System (EPICS) to Windows CE 3.0 (WCE) for the Pocket PC (PPC), and this paper describes the issues involved. The PPC was chosen because the WCE application programming interface (API) for the PPC is a subset of the Win32 API, which EPICS already supports, and because PPC devices tend to have more memory than other PDAs. PDAs provide several ways to connect to a network, using wired or wireless Compact Flash or PCMCIA Ethernet cards and modems. It is the recent advent of readily available wireless networks that makes using the portable PDA interesting. The status and issues surrounding the various kinds of wireless systems available are presented.

physics/0111041

Marty Kraimer

M. R. Kraimer (1), J. B. Anderson (1), J. O. Hill (2), W. E. Norum (3) ((1) Argonne National Laboratory, (2) Los Alamos National Laboratory, (3) University of Saskatchewan)

EPICS: A Retrospective on Porting iocCore to Multiple Operating Systems

Poster Paper WEBT002 at ICALEPCS 2001, 3 pages, 2 tables PDF

eConf C011127 (2001) WEBT002

physics.ins-det

An important component of EPICS (Experimental Physics and Industrial Control System) is iocCore, which is the core software in the IOC (input/output controller) front-end processors. At ICALEPCS 1999 a paper was presented describing plans to port iocCore to multiple operating systems. At that time iocCore only supported vxWorks, but now it also supports RTEMS, Solaris, Linux, and WinNT. This paper describes some key features of how iocCore supports multiple operating systems.

physics/0111044

J. M. Nogiec

J.M. Nogiec, K. Trombly-Freytag, D. Walbridge, E. Desavouret

An XML Driven Framework for Test Control and Data Analysis

ICALEPCS 2001, November 2001, (THAP073) 3 pages, PDF

eConf C011127 (2001) THAP073

physics.ins-det physics.comp-ph

An extensible, component-based framework has been developed at Fermilab to promote software reuse and provide a common platform for developing a family of test and data analysis systems. The framework allows for configuring applications from components through the use of XML configurations. It can be easily extended by adding new components and many application independent components are already provided with the framework. The core of the system has been developed in Java which guarantees its portability and facilitates the use of object-oriented development technologies.

physics/0111045

Pilar Marroquin

Pilar Marroquin

Integrating Externally Developed Systems For SNS Linac Cooling And Vacuum

This paper for the ICALEPCS 2001 conference, San Jose, CA, USA, November 27-30 2001, (TUAP063), 3 pages, PDF

eConf C011127 (2001) TUAP063

TUAP063

physics.ins-det

External contractors are developing the local cooling and vacuum control systems for the Spallation Neutron Source (SNS) linac. Soon these systems will be integrated into the facility-wide controls system. Allen-Bradley Logix5000 series programmable controllers, populated with appropriate input/output modules, were selected as the local controllers. These controllers will be interfaced to the facility-wide control system via VME systems with PowerPC processors running the Wind River VxWorks operating system and Experimental Physics and Industrial Control System (EPICS) front-end controller software. This paper describes the interface and integration issues driven by project, cooling system and vacuum system requirements and hardware selections.

physics/0111046

Richard A. Lerche

R. A. Lerche, G. W. Coutts, L. J. Lagin, R. A. Nyholm, N. R. Sewall, R. D. Stever, J. D. Wiedwald, J. Larkin, S. Stein, R. Martin

The NIF Integrated Timing System - Design and Performance

Contributed conference paper for International Conference on Accelerators & Large Experimental Physics Control Systems ICALEPCS 2001, San Jose, California, November 27-30, 2001 (TUAP069) 3 pages, PDF

eConf C011127 (2001) TUAP069

physics.ins-det

The National Ignition Facility (NIF) will contain the world's most powerful laser. NIF requires more than 1500 precisely timed trigger pulses to control the timing of laser and diagnostic equipment. The Integrated Timing System applies new concepts to generate and deliver triggers at preprogrammed times to equipment throughout the laser and target areas of the facility. Trigger pulses during the last 2 seconds of a shot cycle are required to have a jitter of less than 20 ps (rms) and a wander of less than 100 ps (max). Also, the Timing System allows simultaneous, independent use by multiple clients by partitioning the system hardware into subsets that are controlled via independent software keys. The hardware necessary to implement the Integrated Timing System is commercially available. -- This work is performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under contract No. W-7405-Eng-48.

physics/0111047

Daniel Sigg

D. Sigg, H. Rong, P. Fritschel, M. Zucker, R. Bork, N. Mavalvala, D. Ouimette, and G. Gonzalez

Readout and Control of a Power-recycled Interferometric Gravitational-wave Antenna

Presentation at ICALEPCS 2001, San Jose, November 2001, (WECT003), 3 pages

eConf C011127 (2001) WEcT003

physics.ins-det

Interferometric gravitational wave antennas are based on Michelson interferometers whose sensitivity to small differential length changes has been enhanced by adding multiple coupled optical resonators. The use of optical cavities is essential for reaching the required sensitivity, but sets challenges for the control system which must maintain the cavities near resonance. The goal for the strain sensitivity of the Laser Interferometer Gravitational-wave Observatory (LIGO) is 10^-21 rms, integrated over a 100 Hz bandwidth centered at 150 Hz. We present the major design features of the LIGO length and frequency sensing and control system which will hold the differential length to within 5 10^-14 m of the operating point. We also highlight the restrictions imposed by couplings of noise into the gravitational wave readout signal and the required immunity against them.

physics/0111048

Rolf Keitel

Rolf Keitel

Generating EPICS IOC Databases from a Relational Database - a Different Approach

ICALEPCS01 WEAPO71

eConf C011127 (2001) WEAP071

physics.acc-ph

The EPICS based control system of the ISAC radioactive beam facility uses the CapFast schematic editor to construct the IOC function-block databases. This allows a self-documenting graphical representation of the IOC software using a hierarchical, object-like software structure with reusable components. On the other hand, the control system is quarterbacked by a relational database, which contains all device information. Using database reports and Perl scripts, a device instantiation method was developed which generates top-level schematic files in CapFast format. This method exploits the advantages of device data entry and reporting using a relational database system while maintaining the graphical representation of the IOC database.

physics/0111049

Robert D. Demaret

R. D. Demaret, R. D. Boyd, E. S. Bliss, A. J. Gates, J. R. Severyn

Beam Diagnostics Systems For The National Ignition Facility

3 pages, 4 figures, ICALEPCS conference, Lawrence Livermore National Labority, National Ignition Facility

eConf C011127 (2001) FRAT002

UCRL-JC-143316

physics.ins-det

The National Ignition Facility laser focuses 1.8 Mega-joules of ultraviolet light (wavelength 351 nano-meters) from 192 beams into a 600-micro-meter-diameter volume. Effective use of this output in target experiments requires that the power output from all the beams match within 8% over their entire 20-nanosecond waveform. The scope of NIF beam diagnostics systems necessary to accomplish this task is unprecedented for laser facilities. Each beam line contains 110 major optical components distributed over a 510 meter path, and diagnostic tolerances for beam measurement are demanding. Total laser pulse energy is measured with 2.8% precision, and the inter-beam temporal variation of pulse power is measured with 4% precision. These measurement goals are achieved through use of approximately 160 sensor packages that measure the energy at five locations and power at 3 locations along each beamline using 335 photodiodes, 215 calorimeters and 36 digitizers. Successful operation of such a system requires a high level of automation of the widely distributed sensors. Computer control systems provide the basis for operating the shot diagnostics with repeatable accuracy, assisted by operators who oversee system activities and setup, respond to performance exceptions, and complete calibration and maintenance tasks.

physics/0111050

Kenji Tamasaku

Y. Furukawa, M. Ishii, T. Nakatani, T. Ohata

Development of an Interpreter Program for an Equipment Control

Poster Presentation for the ICALEPCS'2001 Paper Status Number : WEAP033

eConf C011127 (2001) WEAP033

physics.acc-ph physics.ins-det

A message oriented software scheme is used for the SPring-8 beamline control. In the early stage, we developed customized control programs for each beamline. As the number of beamlines increased, however, it became necessary to introduce a general software scheme that cloud handle the control sequence for every beamline. We developed a new server program, Command Interpreter (CI), as a software framework. The CI interprets a high-level compound message issued from client programs and decomposes it to a set of primitive control messages. The message are sent to the VME computers afterwards. For flexibility, the operation sequences specific to the individual baemline component are standardized and defined in the interface definition files. Using the CI, the response time overhead is reduced to 26% and the XAFS measurement time also decreases by about 50%.

physics/0111051

Ralph C. Baer

Ralph C. Baer, Hartmut Eickhoff, Thomas Haberer

Status and Controls Requirements of the Planned Heavy Ion Tumor Therapy Accelerator Facility HICAT

Paper for ICALEPCS 2001 Conference (Poster), Paper TUAP031, PDF (from Word), 3 pages, 1 embedded figure

eConf C011127 (2001) TUAP031

physics.acc-ph

The HICAT project is a Heavy Ion accelerator for light ion Cancer Treatment to be built for the clinics in Heidelberg, Germany. It consists of a 7 MeV/u linac, a compact synchrotron and three treatment places, one of them equipped with a 360 degree gantry beam-line. The facility will implement the intensity controlled raster-scanning technique that was developed and successfully demonstrated at GSI with over 100 patients at present. In order to produce the beams with the characteristics requested by the treatment sequencer, the accelerator must operate on a pulse-to-pulse basis with different settings. This concept imposes strict and challenging demands on the operation of the accelerators and hence the control system of the facility. The control system should be developed, installed and maintained by and under the complete responsibility of an industrial system provider, using a state-of-the-art system and wide-spread industrial components wherever possible. The presentation covers the status of the project and the requirements on the control system.

physics/0111052

V.V. Lyahov, V.M. Nechshadim

On Stability of Physics Systems

32 pages, 16 figures

Glushcko's Physical & Engineering Laboratory report N-097/01.11.2001

physics.gen-ph

Within the framework of the hypothesis offered by authors about a complex-valued nature of physical quantities the stability of basic equations of the classical physics concerning complex-valued perturbations of parameters and boundary conditions is explored. The conducted examination of nonlinear equations and, what is more important, of linear differential equations shows violation in some cases of the continuous dependence of the solution on the change of imaginary parts of parameters and boundary conditions in the neighborhood of zero. In other words, it was revealed that a small imaginary part may drive the real solution. It may be concluded that a small imaginary part, even if unobservable, is still an inherent characteristic of a physical quantity, being yet something like a hidden parameter, and manifests itself only indirectly forcing the system to move in this or that direction, which may be taken as a basis for experimental testing of the put forward hypothesis about a complex-valued nature of physical quantities.

physics/0111053

Toru Ohata

T. Ohata and T. Masuda

A Study of a Real-Time Operating System on the Intel-Based Vme Controllers

3 pages paper for ICALEPCS 2001 conference, PDF format

eConf C011127 (2001) THAP039

THAP039

physics.acc-ph

In this paper, we described the performance differences between VME-based controllers, HP743rt/HP-RT and IA-based platforms. We measured some kind of real-time benchmarks and discussed a relation of architecture dependences.

physics/0111054

Harald Kleines

H. Kleines, P. Wuestner, K. Settke, K. Zwoll

Implementation of JFPC (Java for Process Control) under Linux - a mechanism to access industrial I/Os in a JAVA/Linux environment

Talk at ICALEPCS01, San Jose

eConf C011127 (2001) WEBT004

physics.ins-det

Using JAVA for process control requires the access to I/O-Hardware. This problem is addressed in several ongoing standardisation efforts for Real Time Java. A spin-off of these standardisation efforts is the Siemens product JFPC (Java for Process Control), which is based on the ideas of OPC (OLE for Process Control). It is available under the proprietary RT kernel RMOS and under Windows NT. Based on a contract with Siemens, ZEL - the central electronics facility of Forschungszentrum Juelich - has implemented JFPC under Linux. Additionally, several JFPC providers, e.g for accessing industrial components via PROFIBUS DP have been implemented.

physics/0111055

Kuotung Hsu

Jenny Chen, C. J. Wang, C. H. Kuo, K. H. Hu, C. S. Chen, K. T. Hsu

Data Acquisition and Uesr Interface of Beam Instrumentation System at SRRC

ICALEPCS 2001 poster paper (WEAP035), 3 pages, PDF

eConf C011127 (2001) WEAP035

physics.ins-det

Data acquisition systems for the accelerator complex at SRRC composed various hardware and software components. Beam signals are processed by related processing electronics, and connect to control system by various type of interfaces in data acquisition front-end. These front-end include VME crates, personal computers and instruments bus adapters. Fast Ethernet connected all elements together with control consoles. User interface is running on control console. Real-time data capture; display and alaysis are supported on control console. Analysis tools based on Matlab scripts are adopted. Hardware and software implementation of the system will be presented. User interface supports are also described.

physics/0111056

Ludwig Hechler

Ludwig Hechler

Converting Equipment Control Software from Pascal to C/C++

ICALEPCS 2001, Poster WEAP034, 3 pages, Latex

eConf C011127 (2001) WEAP034

physics.acc-ph

The equipment control (EC) software of the GSI accelerators has been written entirely in Pascal. Modern software development is based on C++ or Java. To be prepared for the future, we decided to convert the EC software from Pascal to C in a first step. Considering the large amount of software, this is done automatically as far as possible. The paper describes our experiences gained using a Pascal to C translator, Perl scripts, and, of course, some manual interaction.

physics/0111057

Matthias Clausen

Matthias Clausen (DESY & SLAC), Piotr Bartkiewicz (DESY & FPNT/AGH), Alexei Dmitrovski, Albert Kagarmanov (DESY & IHEP), Zoltan Kakucs (DESY), Greg White, Hamid Shoaee (SLAC)

An XML Driven Graphical User Interface and Application Management Toolkit

Talk on ICALEPCS'2001 in San Jose (THCT005)3 pages PDF

eConf C011127 (2001) THcT005

THCT005

physics.ins-det

In the past, the features of a user interface were limited by those available in the existing graphical widgets it used. Now, improvements in processor speed have fostered the emergence of interpreted languages, in which the appropriate method to render a given data object can be loaded at runtime. XML can be used to precisely describe the association of data types with their graphical handling (beans), and Java provides an especially rich environment for programming the graphics. We present a graphical user interface builder based on Java Beans and XML, in which the graphical screens are described textually (in files or a database) in terms of their screen components. Each component may be a simple text read back, or a complex plot. The programming model provides for dynamic data pertaining to a component to be forwarded synchronously or asynchronously, to the appropriate handler, which may be a built-in method, or a complex applet. This work was initially motivated by the need to move the legacy VMS display interface of the SLAC Control Program to another platform while preserving all of its existing functionality. However the model allows us a powerful and generic system for adding new kinds of graphics, such as Matlab, data sources, such as EPICS, middleware, such as AIDA[1], and transport, such as XML and SOAP. The system will also include a management console, which will be able to report on the present usage of the system, for instance who is running it where and connected to which channels.

physics/0111059

Toru Fukui

T. Fukui, M. Ishii, R. Tanaka, T. Masuda, T. Ohata

Toward a Reliable Gigabit Network - an Upgrade of the Spring-8 Network

International Conference on Accelerator and Large Experimental Physics Control Systems San Jose, California, November 27-30, 2001, (THDT005), 3 pages, PDF genarated by MS-Word 98 on MAC

eConf C011127 (2001) THDT005

physics.acc-ph physics.ins-det

The SPring-8 controls network has maintained accelerator operations in high reliability and shown good performance during the past years. To cope with the increase of loads on the network due to faster data acquisition and the addition of equipment data, networking hardware has been installed in the last few years. The upgraded network replaces the original FDDI backbone and switches with mixed FDDI/gigabit ethernet and Layer-3 switches. It is necessary to keep the double ring topology for the FDDI and introduce link aggregation technology for the gigabit ethernet to maintain the full redundancy and bandwidth of the system. This paper will discuss the network performance of the gigabit ethernet including its latency and redundancy. We also discuss a future plan for the network including Quality-of-Service over the gigabit ethernet.

physics/0111060

Udo Krause

U. Krause, V. RW Schaa

Re-Engineering of the GSI Control System

ICALEPCS 2001, Talk WEAT002, 3 pages, Latex

eConf C011127 (2001) WEAT002

physics.acc-ph

After more than 12 years of operation without substantial revision a modernization of the control system at GSI is overdue. A strategy to adapt the system to future needs is outlined. The system has to support a specific environment of which the main features are described. More flexibility than in the current system can be achieved while still using many parts of the actual system.

physics/0111061

Changhor Kuo

C. H. Kuo, Jenny Chen, C. J. Wang, K. H. Hu, C. S. Chen, K. T. Hsu

Orbit Feedback System for the Storage Ring of SRRC

Poster Paper for ICALEPCS-2001 (WEAP047), 3 pages, pdf

eConf C011127 (2001) WEAP047

physics.ins-det

Orbit feedback system plays crucial roles for the operation of the 3rd generation light source. There are various issues in orbit feedback system should be addressed to achieve ultimate performance. The orbit feedback system in SRRC is upgraded recently to satisfy the requirement of demanding users. Based upon operational experiences of the last few years, new system was designed with more robustness and flexibility. Performance analysis tools are also developed to monitor system performance. Algorithms for feedback control, data acquisition and analysis are described and measurement is also presented.

physics/0111062

Yoshihiro Suzuki

Y.Suzuki, M.Ieiri, Y.Katoh, E.Kusano, M.Minakawa, H.Noumi, M.Takasaki, K.H.Tanaka, Y.Yamanoi

GPIB Address Converter

ICALEPCS 2001 Conference, San Jose, CA, 27-30 November 2001, Paper TUAP052

eConf C011127 (2001) TUAP052

physics.ins-det physics.acc-ph

A GPIB address converter (GAC) has been constructed. This paper reports on the function and test results. The GAC has two GPIB connectors (upper and lower ports). The upper port has a GPIB primary address, and connected to a GPIB system controller. The lower port acts as a GPIB controller of the lower side GPIB line. The GPIB system controller can access the lower side GPIB devices through the GAC by using an extended two-byte address function. The two-byte address (primary + secondary) is shown in the combination of the GAC address and the address of the lower side device. The GAC converts the secondary address into the primary address of the lower side GPIB device. By using 30 GACs, the GPIB system controller can access 930 devices assigned only primary address.

physics/0111063

Craig R. Wuest

E.I. Moses

The National Ignition Facility: Status and Plans for Laser Fusion and High-Energy-Density Experimental Studies

Paper submitted for ICALEPCS

eConf C011127 (2001) TUAI001

UCRL-JC-142223

physics.plasm-ph physics.gen-ph

The National Ignition Facility (NIF) currently under construction at the University of California Lawrence Livermore National Laboratory (LLNL) is a 192-beam, 1.8-megajoule, 500-terawatt, 351-nm laser for inertial confinement fusion (ICF) and high-energy-density experimental studies. NIF is being built by the Department of Energy and the National Nuclear Security Agency (NNSA) to provide an experimental test bed for the U.S. Stockpile Stewardship Program to ensure the country's nuclear deterrent without underground nuclear testing. The experimental program will encompass a wide range of physical phenomena from fusion energy production to materials science. Of the roughly 700 shots available per year, about 10% will be dedicated to basic science research. Laser hardware is modularized into line replaceable units (LRUs) such as deformable mirrors, amplifiers, and multi-function sensor packages that are operated by a distributed computer control system of nearly 60,000 control points. The supervisory control room presents facility-wide status and orchestrates experiments using operating parameters predicted by physics models. A network of several hundred front-end processors (FEPs) implements device control. The object-oriented software system is implemented in the Ada and Java languages and emphasizes CORBA distribution of reusable software objects. NIF is currently scheduled to provide first light in 2004 and will be completed in 2008.

physics/0111064

Zoltan Kakucs

Zoltan Kakucs, Phil Duval, Matthias Clausen

An EPICS to TINE Translator

Talk at 8th International Conference on Accelerator and Large Experimental Physics Control Systems, ICALEPCS 2001, San Jose, California, from November 27 - 30, 2001 (THBT005) 3 pages, PDF eps figures

eConf C011127 (2001) THBT005

physics.acc-ph

Accelerator control at DESY has in the past been hampered by the 'many-control-systems' syndrome, where different subsystems were controlled by completely different means offering no possibility of intercommunication. Today, practically all subsystems of HERA are controlled by TINE. Important exceptions include the Proton Vacuum(DOOCS), cryogenics control(D3), and the super-conducting electron RF cavities and the power and cooling subsystems, the latter two of which are controlled by EPICS IOCs. A step toward integrating the EPICS IOCs into the HERA mainstream has been taken in that an EPICS to TINE translator process has been written, which runs directly on the EPICS IOC and offers a TINE view of the hardware control to the rest of the control system. This in effect renders the EPICS IOC into a bi-lingual server, and highlights the principal difference between a 'translator' and a 'gateway'. Details of this translator are presented in this paper.

physics/0111066

Johannes van Zeijts

Johannes van Zeijts

Model Driven Ramp Control at RHIC

First draft, Latex, 3 pages, 2 eps figures, ICALEPCS 2001, FRBT004

eConf C011127 (2001) FRBT004

FRBT004

physics.acc-ph

At the Relativistic Heavy Ion Collider (RHIC), magnets are ramped from injection energy to storage energy in several min utes where it is to remain for several hours. The path up the ramp is marked by 'StepStones' where the the optics of the ma chine, which can change dramatically when we perform a beta*-squeeze, is given in units like Quadrupole focusing strengt h or Corrector-Dipole angle. The machine is tuned at these Stepstones, and at Injection or Storage, by specifying physic s properties like Tunes and Chromaticities. An on-line model server handles conversion to magnet strengths, and predicts the optics along the whole ramp. We will describe the underlying principles, the client-server environment, including on-line model servers, Ramp Manager and Editor, and present operational experience with the system.

physics/0111067

Anton Mezger

A.C.Mezger, D.Anicic, T.Blumer, I.Jirousek

Integration of a New Knobbox in the PSI Control Systems ACS and EPICS

Paper submitted at the8th International Conference on Accelerator and Large Experimental Physics Control Systems as Poster (PSN WEAP009)

eConf C011127 (2001) WEAP009

physics.acc-ph

Integration of a new Knob-Box in the PSI Control Systems ACS and Epics. Operation of the PSI cyclotrons has always relied heavily on manual control. Tuning of our high intensity beams for minimum losses is an art still depending on personal skill. An ergonomically good design of the knob box is therefore essential for good operation. The age of the previous design, and the request, to implement the ACS knob box in the SLS control system based on EPICS, was an opportunity for a redesign. The new knob box is an autonomous node in the system. It is based on industrial pc104 hardware with LINUX as the operating system. CDEV and ACS-communication provide the interface to the respective control systems.

physics/0111068

Klemen Zagar

Klemen Zagar, Mark Plesko, Matej Sekoranja, Gasper Tkacik, Anze Vodovnik

The Control System Modeling Language

3 pages, 2 figures, 8th ICALEPCS conference, paper THCT004

eConf C011127 (2001) THcT004

physics.acc-ph

The well-known Unified Modeling Language (UML) describes software entities, such as interfaces, classes, operations and attributes, as well as relationships among them, e.g. inheritance, containment and dependency. The power of UML lies in Computer Aided Software Engineering (CASE) tools such as Rational Rose, which are also capable of generating software structures from visual object definitions and relations. UML also allows add-ons that define specific structures and patterns in order to steer and automate the design process. We have developed an add-on called Control System Modeling Language (CSML). It introduces entities and relationships that we know from control systems, such as "property" representing a single controllable point/channel, or an "event" specifying that a device is capable of notifying its clients through events. Entities can also possess CSML-specific characteristics, such as physical units and valid ranges for input parameters. CSML is independent of any specific language or technology and generic such that any control system can be described with it. Simple transformation scripts map CSML defined structures to APIs and tools such as EPICS, CDEV, SCADA, Abeans, BACI and generate the appropriate database or source files. Advantages of control system development with CSML are discussed on a concrete example of a bending magnet's power supply in a synchrotron accelerator.

physics/0111069

Gert-Ludwig Ingold

J\"org Lehmann, Gert-Ludwig Ingold, Peter H\"anggi (U Augsburg)

Incoherent charge transport through molecular wires: interplay of Coulomb interaction and wire population

18 pages, 8 figures, elsart.cls v2.18 included

Chem. Phys. 281, 199-209 (2002)

10.1016/S0301-0104(02)00344-0

physics.chem-ph cond-mat.mes-hall

The influence of Coulomb interaction on the electron transport through molecular wires is studied in the regime of incoherent tunneling. In the limit of strong Coulomb repulsion, the current for spinless electrons is determined. It is shown that the voltage profile along the wire crucially influences the dependence of the current on the wire length. Upon inclusion of the spin degree of freedom one finds a blocking effect which depends both on the interaction strength and on the population of the wire. For finite Coulomb interaction, the temperature dependence of the blocking is studied and it is shown that several regimes with different blocking strength may exist.

physics/0111070

Laurent Sanchez-Palencia

Laurent Sanchez-Palencia, Peter Horak and Gilbert Grynberg

Spatial diffusion in a periodic optical lattice: revisiting the Sisyphus effect

accepted for publication in Eur. Phys. J. D

European Physical Journal D 18, 353 (2002)

10.1140/epjd/e20020041

physics.atom-ph

We numerically study the spatial diffusion of an atomic cloud experiencing Sisyphus cooling in a three-dimensional lin$\bot$lin optical lattice in a broad range of lattice parameters. In particular, we investigate the dependence on the size of the lattice sites which changes with the angle between the laser beams. We show that the steady-state temperature is largely independent of the lattice angle, but that the spatial diffusion changes significantly. It is shown that the numerical results fulfil the Einstein relations of Brownian motion in the jumping regime as well as in the oscillating regime. We finally derive an effective Brownian motion model from first principles which gives good agreement with the simulations.

physics/0111071

Maxim Vrazhnov

K. Gubrienko (1), I. Krouptchenkov (1), S. Makonin (1), V. Seleznev (1), F. Solodovnik (1), A. Sytin (1), M. Vrazhnov (1), K. Wittenburg (2) ((1) IHEP, Protvino, Russia,(2) DESY, Hamburg, Germany)

Precision geometric parameter gage for synchrotron radiation

3 pages, 5 figures, poster

eConf C011127 (2001) THAP048

physics.ins-det

This article includes the description of the geometric parameter gage device prototype for synchrotron radiation of HERA collider (DESY). The system construction which capable to measure photo current, caused by such a radiation in a refractory metal, described here. The system component parts are: measuring heads and photo current measuring electronics designed by IHEP, stepper motor by Vacuum Generators with HEDS-550X encoder by Hewlett Packard, PCI-STEP-4CX 4-Axis Closed Loop Step controller by National Instruments. The device is controlled by means of Microsoft Visual Basic program using Value Motion Windows Libraries. The device prototype was tested in the beam of the DORIS storage ring.

physics/0111073

John C. Collins

J.C. Collins, M. Ball, B. Broderick, J. Katuin, Wm. Manwaring, N. Schreuder

Design of the MPRI Control System

Poster paper submitted to ICALEPCS'01, San Jose, Nov. 2001, PSN#TUA016, 3 pages, 1 figure, MS Word

eConf C011127 (2001) TUAP016

physics.acc-ph

The Indiana University Cyclotron Facility (IUCF) is in the process of building the Midwest Proton Radiation Institute (MPRI). This involves refurbishing the 200MeV cyclotron and building new facilities for the purpose of providing clinical treatment of human cancer tumors. First patients are expected in the Spring of 2003. This paper presents the design and implementation to date of the controls, hardware and software, for both accelerator and treatment areas. Particular attention is placed on issues of personnel safety and control system security, development of inexpensive VMEbus boards with emphasis on the use of MicroChip PIC processors, beam diagnostics and monitoring and the use of commercial robots and vision systems for patient positioning.

physics/0111075

William R. DeVan

W.R. DeVan, E.L. Williams Jr

Plans for the Spallation Neutron Source Integrated Control System Network

Poster paper for ICALEPCS conference, San Jose, CA, USA, November 2001, PSN TUAP055, 3 pages, MS Word 2000 format

eConf C011127 (2001) TUAP055

TUAP055

physics.acc-ph

The SNS control system communication network will take advantage of new, commercially available network switch features to increase reliability and reduce cost. A standard structured cable system will be installed. The decreasing cost of network switches will enable SNS to push the edge switches out near the networked devices and to run high-speed fiber communications all the way to the edge switches. Virtual Local Area Network VLAN) technology will be used to group network devices into logical subnets while minimizing the number of switches required. Commercially available single-board computers with TCP/IP interfaces will be used to provide terminal service plus remote power reboot service.

physics/0111077

Jay Heefner

R. Bork, R. Abbott, D. Barker, J. Heefner (LIGO Laboratory, California Institute of Technology, Pasadena, CA)

An Overview of the LIGO Control and Data Acquisition System

5 pages

eConf C011127 (2001) TUBI001

physics.ins-det physics.gen-ph physics.optics

The LIGO Control and Data system (CDS) features a tightly coupled and highly integrated control and data acquisition system. Control of the interferometers requires many Multiple Input Multiple Output (MIMO) control loops closed both locally and across the 4-kilometer interferometer arm lengths. In addition to providing the closed loop control, the control systems front end processors act as Data Collection Units (DCU) for the data acquisition system. Data collected by these front ends and the data acquisition system must be collected and time stamped to an accuracy of 1 microsecond and made available to on-line analysis tools such as the Global Diagnostics System (GDS)[1]. Data is also sent to the LIGO Data Analysis System (LDAS)[2] for long-term storage and off-line analysis. Data rates exceed 5 Mbytes per second per interferometer continuous. Connection between the various front end processors and the data acquisition system is achieved using fiber optic reflective memory networks. Both controls and data acquisition systems use VME hardware and VxWorks operating systems. This paper will present an overview of the LIGO CDS and discuss key aspects of its design.

physics/0111080

Alexander Loukiantsev

V. Kovaltsov (1), A. Loukiantsev (1), A. Matyushin (1), V. Milyutkin (1), I. Romanov (1), V. Seleznev (1), A. Sytin (1), M. Clausen (2) (IHEP, Protvino, Russia (1), DESY, Hamburg, Germany (2))

Upgrading of the beam diagnostic system of U-70 beam transfer lines

3 pages, 3 figures, poster

eConf C011127 (2001) WEAP005

physics.ins-det physics.acc-ph

The beam diagnostic system of U-70 beam transfer lines (beam profiles, intensity and beam losses measurements) was designed in the beginning of 80-th on the base of 8-bit microprocessor, SUMMA hardware and home made serial communication link. Because of the maintenance problems the decision was taken to upgrade the hardware and software parts of the system.

physics/0111081

Rod B. Nussbaumer

R. Nussbaumer, D. Dale, H. Hui, J. Richards, P. Levy

Laser Stabilization Controls for the ISAC Beam Polarizer

ICALEPS01 TUAP065

eConf C011127 (2001) THAP065

physics.acc-ph

The ISAC polarized beam facility uses a Ti:Sapphire laser for producing spin-polarized beams of short-lived radioactive isotopes, initially 7Li. The laser power and spectral content must be tightly controlled and monitored. The control system to accomplish this task uses techniques that combine operator interface, data reduction, and closed loop automation. The laser stabilization application uses input data acquired from a spectrum analyzer, in the form of a waveform array repetitively acquired from a GPIB-interfaced oscilloscope. A Labview based operator interface allows the selection of features from within the waveform, which are then used as the basis for closed loop control, in concert with the existing EPICS control system software and related hardware. Part of the challenge stems from using input data which are subject to human interpretation and require distillation into a hard numeric format suitable for use in a control system.

physics/0111082

Eric Bjorklund

E. Bjorklund

Toward a General Theory of Control Knobs

International Conference on Accelerator and Large Experimental Physics Control Systems (ICALEPCS 2001) PSN = THAP071 12/18/02: Minor revision after reviewer comments

eConf C011127 (2001) THAP071

LA-UR-01-2033

physics.acc-ph

Experience using hardware knobs as an operator interface for controlling equipment has varied considerably at different facilities. Reactions have ranged from "indispensable" at some facilities, to "virtually useless" at others. In this paper, we will attempt to outline some basic principles for successful knob implementation. These principles derive from our own experience with control knobs at the LANSCE Accelerator Complex and our recent effort to adapt our control knobs to EPICS. Topics to be covered include what the operator needs the knob to do, what the knob needs to know about the device it is controlling, and knob scaling issues. Advanced topics such as closed-loop, PID, and aggregate knobs are left as topics for future papers.

physics/0111083

Christine A. Treml

Chrisine A. Treml, Stanley K. Brown, John D. Bernardin

Resonance Control Cooling System for a Proto-Type Coupled Cavity Linac

3 Page Paper for procedings from and to accompany poster session for: ICALEPCS 2001 8th International Conference on Accelerator and Large Experimental Physics Control Systems San Jose, California, from November 27 - 30, 2001

eConf C011127 (2001) WEAP076

physics.acc-ph

Los Alamos National Laboratory (LANL) is designing a coupled cavity linac (CCL) for the Spallation Neutron Source (SNS) being built at Oak Ridge National Laboratory (ORNL). As part of the design process, a proto-type, Hot Model, consisting of two segments of the SNS CCL was manufactured and installed at LANL. An RF source was applied to the Hot Model to determine the success of the cavity design, the effectiveness of the control algorithms and cooling systems, and the validity of the Resonance Control Cooling System (RCCS) model used during the Hot Model design. From a system controls perspective, an overview of the hot model, a description of the RCCS, and the pertinent data from the RF tests will be presented.

physics/0111084

Donald A. Dohan

D. A. Dohan (Advanced Photon Source, Argonne, IL)

Decision Support System for the APS Control System

Presented (WEET001) at ICALEPCS 2001, San Jose CA, Nov. 27-30, 2001 3 pages, 1 figure, PDF

eConf C011127 (2001) WEDT001

physics.acc-ph

The Advanced Photon Source is now in its fifth year of routine beam production. The EPICS-based [1] control system has entered the phase in its life cycle where new control algorithms must be implemented under increasingly stringent operational and reliability requirements. The sheer volume of the control system (~270,000 records, ~145 VME-based input-output controllers (IOCs), and ~7,000,000 lines of EPICS ASCII configuration code), presents a daunting challenge for code maintenance. The present work describes a relational database that provides an integrated view of the interacting components of the entire APS control system, including the IOC low-level logic, the physical wiring documentation, and high-level client applications. The database is extracted (booted) from the same operational CVS repository as that used to load the active IOCs. It provides site-wide decision support facilities to inspect and trace control flow and to identify client (e.g., user interface) programs involved at any selected point in the front-end logic. The relational database forms a basis for generalized documentation of global control logic and its connection with both the physical I/O and with external high-level applications.

physics/0111085

Buceti Giuliano

A. Bertocchi, V. Bozzolan, G. Buceti, C. Centioli, D. Di Muzio, F. Iannone, G. Mazza, M. Panella, V. Vitale

Technology Update of a Control System Trough Corba Bus

Poster at 8th International Conference on Accelerator and Large Experimental Physics Control Systems (THAP004), PDF, 3 pages

eConf C011127 (2001) THAP004

physics.acc-ph physics.ins-det

After more than 10 years of activity, FTU (Frascati Tokamak Upgrade) has to face the problem of taking advantage of the new hardware and software technology saving all the investments yet done. So, for example, the 20 years old Westinghouse PLCs (communicating only through a serial line) have to be leaved in operation while a web-based tool has to be released for plan monitoring purpose. CORBA bus has been demonstrated to be the answer to set up the communication between old and new hardware and software blocks. On FTU the control system is based on Basestar, a Digital/Compaq software suite. We will describe how the real time database of Basestar is now accessed by Java graphic tools, LabView and, in principle, any package accepting external routines. An account will be also done in the data acquisition area where a Camac serial highway driver has been integrated in the new architecture still through the CORBA bus

physics/0111088

Reinhard Bacher

Reinhard Bacher, Philip Duval, Stephen Herb

What are the Controls Requirements for the Global Accelerator Network?

ICALEPCS 2001 THAP056

eConf C011127 (2001) THAP056

physics.acc-ph

The Global Accelerator Network is a proposed model for remote operation of a future large accelerator by the partners of an international collaboration. The remote functionality would include not only routine operation and machine studies, but also hardware diagnostic tests and software maintenance and development, so the control system must offer both high and low level remote access to the accelerator and its components. We discuss in this paper some of the special requirements, and how they might be satisfied using current or developing technology, such as web-based applications and industrial automation standards. The choices made must be acceptable to the collaboration, but will also have a strong influence on its effectiveness. The biggest technical challenge is likely to be the middle layer software which is responsible for system integration, automation, and presentation of the machine state to the operating staff.

physics/0111089

Phlip Duval

J. Dovc, M. Kadunc, Y.Oku, M. Plesko, G.Tkacik, K. Bartkiewicz, P. Duval

New Abeans for TINE Java Control Applications

ICALEPCS 2001

eConf C011127 (2001) THAP025

THAP025

physics.acc-ph

Abeans [1] (wide-interface accelerator Java beans developed at JSI) have in the past been used with great success in control applications at ANKA and ESO and on test cases at the SLS and Riken. At DESY, TINE [2] is used as the principal control system for HERA as well as the intercommunication protocol among the HERA experiments. To date, most TINE-based client-side applications have been written using ACOP [3] (a narrow-interface accelerator component) in Visual Basic (VB), which has provided a remarkably powerful developing environment for generating professional control applications. Currently, however, VB control applications can only run on Windows-based desktop machines and consoles. As it is often desirable to provide certain control applications on non-Windows platforms (or indeed over the Web), we have created an equally powerful developing environment based on Java and the next release of Abeans, where an ACOP-like narrow-interface bean has been developed. Like ACOP, the Abean itself accepts plugs from various communication protocols, but was brought to fruition at DESY using the TINE Java class. Details concerning matching Abeans and TINE, as well as the pros and cons of wide versus narrow interfaces will be presented below. Several applications will also presented along with the results of benchmarking against similar VB applications.

physics/0111092

Jan Pusina

Jan Pusina

Optimized Filling of the ALS Storage Ring

3 pages, 3 figures, for ICALEPCS 2001

eConf C011127 (2001) WEAP053

WEAP053

physics.acc-ph

The Storage Ring at the Advanced Light Source is capable of being filled in selectable buckets. Typically, 276 consecutive buckets out of 328 possible are selected. It has been found that the amount of charge injected is not uniform bucket-to-bucket, sometimes varying by 100% or more. This variability causes problems with beam stability, and it may shorten the beam lifetime. We have devised a feedback system that allows for beam filling in an orderly manner, yielding bunch heights uniform to within 17%. At fill time, multiple bunches are injected into the Storage ring first, then, using feedback, selected single bunches are used to top off the fill.

physics/0111093

Simon Berkovich

S.Y. Berkovich

On the "barcode" functionality of the DNA, or The phenomenon of Life in the physical Universe

52 pages, 2 textual figures, 1 bitmap figure

GWU-IIST-2001-01

physics.bio-ph physics.comp-ph q-bio

The information contained in the genome is insufficient for the control of organism development. Thus, the whereabouts of actual operational directives and workings of the genome remain obscure. In this work, it is suggested that the genome information plays a role of a "barcode". The DNA structure presents a pseudo-random number(PRN)with classification tags, so organisms are characterized by DNA as library books are characterized by catalogue numbers. Elaboration of the "barcode" interpretation of DNA implicates the infrastructure of the physical Universe as a seat of biological information processing. Thanks to the PRNs provided by DNA, biological objects can share these facilities in the Code Division Multiple Access (CDMA) mode, similarly to cellular phone communications. Figuratively speaking, populations of biological objects in the physical Universe can be seen as a community of users on the Internet with a wireless CDMA connection. The phenomenon of Life as a collective information processing activity has little to do with physics and is to be treated with the methodology of engineering design. The concept of the "barcode" functionality of DNA confronts the descriptive scientific doctrines with a unique operational scheme of biological information control. Recognition of this concept would require sacrificing the worldview of contemporary cosmology.

physics/0111094

Rolf Keitel

R. Keitel and R. Nussbaumer

Automated Checking and Visualization of Interlocks in the ISAC Control System

ICALEPCS01 WEAPO70

eConf C011127 (2001) WEAP070

physics.acc-ph

The EPICS based control system of the ISAC radioactive beam facility supervises several sub-systems, which are controlled by PLCs. Most of the devices are protected by non-trivial interlocks, which are implemented with ladder-logic software. Detailed information on interlock state and the individual interlock conditions are accessible for each device at the EPICS operator interface level. With the increasing number of ISAC devices, the interactive generation and maintenance of these displays with standard EPICS tools was too labor-intensive and error-prone. Software was developed, which uses a printout of the PLC program as well as reports from the ISAC device database to a) check the interlock implementation in the PLC against interlock specifications in natural language and b) generate device displays with a graphical representation of interlock state and details of interlock conditions.

physics/0111095

Rolf Keitel

R. Keitel, D.Bishop, D.Dale, H.Hui, S.Kadantsev, M.Leross, R.Nussbaumer, J.Richards, E.Tikhomolov, G.Waters

Status Update on the ISAC Control System

ICALEPCS01 TUAPO28

eConf C011127 (2001) TUAP028

physics.acc-ph

Implementation and commissioning of the EPICS based control system for the ISAC radioactive beam facility was completed. The target ion source, mass separator, and low-energy beam-lines started beam production for experiments. In parallel, controls for the accelerator system, a radio-frequency quadrupole followed by a drift-tube linac, and several high-energy beam-lines were implemented and commissioned. The number of controlled devices more than doubled since the last report. An overview of relational database usage, software engineering and quality control methods used will be given.

physics/0111096

Nikolay Malitsky

N.Malitsky, J.Smith, J.Wei

A Prototype of the UAL 2.0 Application Toolkit

ICALEPCS 2001 Conference, San Jose, CA, 27-30 November 2001, THAP013, 3 pages, 4 embedded figures

eConf C011127 (2001) THAP013

physics.acc-ph physics.ins-det

The paper presents a prototype of the accelerator commissioning and simulation application toolkit based on the Unified Accelerator Libraries (UAL) framework. The existing UAL 1.x environment has been implemented as an open collection of C++ and Perl packages that address various tasks of accelerator physics. The UAL 2.0 application toolkit has been developing on the top of the Java infrastructure for integrating it with distributed accelerator control systems. The core part of the toolkit is composed of the Common Accelerator Objects (such as Accelerator, Algorithms, etc.) that form the framework for developing project-specific applications. The toolkit environment is not only limited to Java applications, but also supports the development and integration of high-level scripting codes (e.g. Java Python scripts) and existing C/C++ libraries. The configuration and navigation of the project-specific application system is provided by the XML-based Application Manager.

physics/0111097

Stephen A. Lewis

S. A. Lewis, C. A. Lionberger, P. T. Cull

Status of the Control Sytem for the Front-End of the Spallation Neutron Source

Paper for ICALEPCS 2001, San Jose, CA, 27-30 November, 2001 (TUAP026); 3 pages, 3 figures

eConf C011127 (2001) TUAP026

physics.acc-ph physics.ins-det

The Spallation Neutron Source (SNS) is a partnership between six laboratories. To ensure a truly integrated control system, many standards have been agreed upon, including the use of EPICS as the basic toolkit. However, unique within the partnership is the requirement for Lawrence Berkeley National Lab, responsible for constructing the Front End, to operate it locally before shipping it to the Oak Ridge National Lab (ORNL) site. Thus, its control system must be finished in 2001, well before the SNS completion date of 2006. Consequently many decisions regarding interface hardware, operator screen layout, equipment types, and so forth had to be made before the other five partners had completed their designs. In some cases the Front-End has defined a standard by default; in others an upgrade to a new standard is anticipated by ORNL later. Nearly all Front-End devices have been commissioned with the EPICS control system. Of the approximately 1500 signals required, about 60% are now under daily operational use. The control system is based on "standard architecture"; however, it has a field-bus dominated layout. This paper will discuss some unique interface requirements that led to adding new device families into the EPICS repertoire. It will also describe the choices and trade-offs made for all major areas.

physics/0111099

Octav Marghitu

S. Marghitu, C. Oproiu, C. Dinca, O. Marghitu

Pulsed electron source characterization with the modified three gradient method

Paper THAP068, ICALEPCS 2001, PDF

physics.acc-ph physics.ins-det

Results from the Modified Three Gradient Method (MTGM), applied to a pulsed high intensity electron source, are presented. The MTGM makes possible the non-destructive determination of beam emittance in the space charge presence [1]. We apply the MTGM to an experimental system equipped with a Pierce convergent diode, working in pulse mode, and having a directly heated cathode as electron source. This choice was mainly motivated by the availability of an analytical characterization of this source type [2], as well as the extended use of the Pierce type sources in linear accelerators. The experimental data are processed with a numerical matching program, based on the K-V equation for an axially symmetric configuration [3], to determine the emittance and object cross-over position and diameter. The variation of these parameters is further investigated with respect to both electrical and constructive characteristics of the source: cathode heating current, extraction voltage, and cathode-anode distance.

physics/0111102

Naoyasu Hosoda

N. Hosoda, T. Ohshima, T. Aoki, T. Asaka, H. Ego, K. Fukami, Y. Kawashima, Y. Ohashi, T. Takashima, H. Yonehara

Timing System of SPring-8 Booster Synchrotron

International Conference on Accelerator and Large Experimental Physics Control Systems San Jose, California, November 27-30, 2001, (TUAP046), 3 pages, PDF genarated by MS-Word2000 on Windows98

eConf C011127 (2001) TUAP046

physics.acc-ph

The timing system of SPring-8 booster synchrotron generates various timing signals concerning beam injection, acceleration from 1 GeV to 8 GeV and ejection. We have improved the timing system of the synchrotron giving it better stability and flexibility. This improvement results the other merits of advanced operations, for example, storing electron beam in the synchrotron, changing the injection cycle from 1 Hz to the slower frequency to increase the RF knock-out (RF-KO) operation period and ejecting the low energy beam during ramping up.

physics/0111104

R. Lewis Van Atta

Lewis Van Atta, Mark Perez, Richard Zacharias, William Rivera

The Wavefront Control System for the National Ignition Facility

eConf C011127 (2001) WEcT002

physics.ins-det

The National Ignition Facility (NIF) requires that pulses from each of the 192 laser beams be positioned on target with an accuracy of 50 um rms. Beam quality must be sufficient to focus a total of 1.8 MJ of 0.351-um light into a 600-um-diameter volume. An optimally flat beam wavefront can achieve this pointing and focusing accuracy. The control system corrects wavefront aberrations by performing closed-loop compensation during laser alignment to correct for gas density variations. Static compensation of flashlamp-induced thermal distortion is established just prior to the laser shot. The control system compensates each laser beam at 10 Hz by measuring the wavefront with a 77-lenslet Hartmann sensor and applying corrections with a 39-actuator deformable mirror. The distributed architecture utilizes SPARC AXi computers running Solaris to perform real-time image processing of sensor data and PowerPC-based computers running VxWorks to compute mirror commands. A single pair of SPARC and PowerPC processors accomplishes wavefront control for a group of eight beams. The software design uses proven adaptive optic control algorithms that are implemented in a multi-tasking environment to economically control the beam wavefronts in parallel. Prototype tests have achieved a closed-loop residual error of 0.03 waves rms.

physics/0111105

Chunhong Wang

C.H. Wang, X. C. Kong, G. Lei, S.F. Xu, Q. Le, and J. Zhao

A Prototype of Upgrading Bepc Control System

poster at ICALEPCS'01, 2 pages, 1 figure

eConf C011127 (2001) WEAP007

physics.acc-ph

We will use EPICS toolkit [1] to build a prototype for upgrading BEPC control system. The purposes are for the following three aspects: (1) Setup a network based distributed control system with EPICS. (2) Study some front-end control technology. (3) Merge the existing control systems into EPICS. The hardware architecture consists of three physical layers. The front-end layer is VME crate, PowerPC, VME I/O modules and interface boards (VME-CAMAC and Fieldbus). The back-end layer is SUN workstation, which is used as application development. The two layers are connected via the middle layer which is 100M Ethernet. In order to preserve our investment in the hardware, the existing CAMAC hardware will remain. The CAMAC will be connected to the VME via CAMAC serial highway [2]. The operator interface will be developed with EPICS DM2K. High-level accelerator control applications will be studied as well with EPICS channel access and archive access.

physics/0111106

Yuri Arestov

Yuri Arestov

Polarization transfer in SIDIS for Lambda production

4 pages, 4 figures. Talk given at IX Workshop on High Energy Spin Physics, Dubna, Aug. 2001

physics.gen-ph

Polarization transfer from the longitudinally polarized positron to the final-state quark is considered for the underlying QCD subprocesses giving rise to the reaction e+(pol) + p --> e+ + Lambda(pol) + X at the HERMES energy.

physics/0111108

Teixeira

A.F.F. Teixeira (Centro Brasileiro de Pesquisas Fisicas)

Distances in plane membranes

8 pages, 6 figures, version 2 with corrected commands of figures

CBPF-NF-061/01

physics.bio-ph astro-ph

A flat membrane with given shape is displayed; two points in the membrane are randomly selected; the probability that the separation between the points have a specified value is sought. A simple method to evaluate the probability density is developed, and is easily extended to spaces with more dimensions.

physics/0111110

Nils Berglund

Nils Berglund and Barbara Gentz

Metastability in simple climate models: Pathwise analysis of slowly driven Langevin equations

24 pages, 8 figures. Proceedings of the "Second Workshop on Stochastic Climate Models", Chorin, 9-11 July, 2001

Stoch. Dyn. 2:327-356 (2002)

10.1142/S0219493702000455

WIAS-696

physics.ao-ph nlin.CD

We consider simple stochastic climate models, described by slowly time-dependent Langevin equations. We show that when the noise intensity is not too large, these systems can spend substantial amounts of time in metastable equilibrium, instead of adiabatically following the stationary distribution of the frozen system. This behaviour can be characterized by describing the location of typical paths, and bounding the probability of atypical paths. We illustrate this approach by giving a quantitative description of phenomena associated with bistability, for three famous examples of simple climate models: Stochastic resonance in an energy balance model describing Ice Ages; hysteresis in a box model for the Atlantic thermohaline circulation; and bifurcation delay in the case of the Lorenz model for Rayleigh-B'enard convection.

physics/0111112

Ted D'Ottavio

T. D'Ottavio, B. Frak, J. Morris, T. Satogata, and J. van Zeijts

Description of the RHIC Sequencer System

Poster paper for ICALEPCS 2001 conference, San Jose, USA, (THAP062), 3 pages in PDF format

eConf C011127 (2001) THAP062

physics.acc-ph

The movement of the Relativistic Heavy Ion Collider (RHIC) through its various states (eg. injection, acceleration, storage, collisions) is controlled by an application called the Sequencer. This program orchestrates most magnet and instrumentation systems and is responsible for the coordinated acquisition and saving of data from various systems. The Sequencer system, its software infrastructure, support programs, and the language used to drive it are discussed in this paper. Initial operational experience is also described.

physics/0111113

Paul Jines

P. Jines and B. Craft

PLC Based Upgrades for the CAMD Linac and Storage Ring Control System

Poster Session paper for ICALEPCS 2001 conference, San Jose, California, November 2001 (PSN# WEAP037). 3 pages. PDF format

eConf C011127 (2001) WEAP037

WEAP037

physics.acc-ph

Louisiana State University Center for Advanced Microstructures and Devices (CAMD) began a control system upgrade project in early 1997. At the time, the storage ring was controlled by a VAX/VMS system, primarily using CAMAC for I/O. The injector Linac was controlled by a separate VME/OS/9 system using custom I/O components. The storage ring control system has been replaced with a PC/Linux based system, utilizing the existing CAMAC subsystem [1]. In an effort to both migrate channels away from CAMAC, and integrate the Linac controls with the storage ring controls, a design for upgrades utilizing AutomationDirect.com PLCs was presented [2]. This paper will discuss the detailed design for the Linac PLC based control system, and discuss the status of PLC upgrades for the Vacuum system, Kicker controls, 2nd RF system, and utilities monitoring.

physics/0111114

Mikhail Kalmykov

Alexander Luchinskiy (Johannes Gutenberg-University Mainz, Institute of Physics, Germany), Yakov S. Shifrin (Kharkov State Technical University of Radioelectronics, Ukraine)

Laboratory Modelling of the Earth Radiation Belt

3 pages, LaTeX

physics.space-ph

Method of the laboratory modeling of the Earth radiation belt is presented. Method can be used for the estimation of consequences of global energetic and communication projects realizations.

physics/0111116

Joachim Rahn

K. Buerkmann (1), B. Franksen (1), R. Lange (1), I. Mueller (1), R. Mueller (1), J. Rahn (1), T. Schneegans (1), G. v. Egan (2) ((1) BESSY, Berlin, FRG, (2) EuKontroll, Berlin, FRG)

Corrector Power Supplies with a DAC Resolution up to 24 Bits based on 16 Bit DAC Devices

Poster paper submitted to ICALEPCS'01, San Jose, USA, Nov. 2001, PSN # TUAP050, 1 LaTeX File (3 Pages), 4 EPS-Figure Files, 1 LaTeX-Class File

eConf C011127 (2001) TUAP050

physics.acc-ph

At BESSY the standard 16 bit resolution of the corrector power supplies was insufficient for the continous orbit drift correction. A new sophisticated design of the analog/digital I/O board increases the resolution of the analog output up to 24 bits without suffering on losses in the long term stability or the dynamic range of the correctors. This is achieved by a cost-efficient boarddesign using standard 16 bit DAC devices in an range-overlapping fine/coarse architecture.

physics/0111117

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France) and Ken Sauer (Department of Electrical Engineering, University of Notre Dame, Indiana, USA)

Shape reconstruction in X-ray tomography from a small number of projections using deformable models

Presented at MaxEnt97. Appeared in Maximum Entropy and Bayesian Methods, G.J. Erickson, J.T. Rychert and C.R. Smith (Ed.), Kluwer Academic Publishers (http://www.wkap.nl/prod/b/0-7923-5047-2)

physics.data-an

X-ray tomographic image reconstruction consists of determining an object function from its projections. In many applications such as non-destructive testing, we look for a fault region (air) in a homogeneous, known background (metal). The image reconstruction problem then becomes the determination of the shape of the default region. Two approaches can be used: modeling the image as a binary Markov random field and estimating the pixels of the image, or modeling the shape of the fault and estimating it directly from the projections. In this work we model the fault shape by a deformable polygonal disc or a deformable polyhedral volume and propose a new method for directly estimating the coordinates of its vertices from a very limited number of its projections. The basic idea is not new, but in other competing methods, in general, the fault shape is modeled by a small number of parameters (polygonal shapes with very small number of vertices, snakes and deformable templates) and these parameters are estimated either by least squares or by maximum likelihood methods. We propose modeling the shape of the fault region by a polygon with a large number of vertices, allowing modeling of nearly any shape and estimation of its vertices' coordinates directly from the projections by defining the solution as the minimizer of an appropriate regularized criterion. This formulation can also be interpreted as a maximum a posteriori (MAP) estimate in a Bayesian estimation framework. To optimize this criterion we use either a simulated annealing or a special purpose deterministic algorithm based on iterated conditional modes (ICM). The simulated results are very encouraging, especially when the number and the angles of projections are very limited.

physics/0111118

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

Probabilistic methods for data fusion

Presented at MaxEnt97. Appeared in Maximum Entropy and Bayesian Methods, G.J. Erickson, J.T. Rychert and C.R. Smith (Ed.), Kluwer Academic Publishers (http://www.wkap.nl/prod/b/0-7923-5047-2)

physics.data-an

The main object of this paper is to show how we can use classical probabilistic methods such as Maximum Entropy (ME), maximum likelihood (ML) and/or Bayesian (BAYES) approaches to do microscopic and macroscopic data fusion. Actually ME can be used to assign a probability law to an unknown quantity when we have macroscopic data (expectations) on it. ML can be used to estimate the parameters of a probability law when we have microscopic data (direct observation). BAYES can be used to update a prior probability law when we have microscopic data through the likelihood. When we have both microscopic and macroscopic data we can use first ME to assign a prior and then use BAYES to update it to the posterior law thus doing the desired data fusion. However, in practical data fusion applications, we may still need some engineering feeling to propose realistic data fusion solutions. Some simple examples in sensor data fusion and image reconstruction using different kind of data are presented to illustrate these ideas. Keywords: Data fusion, Maximum entropy, Maximum likelihood, Bayesian data fusion, EM algorithm.

physics/0111119

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France) and H.G. Miller (Department of Physics, University of Pretoria, South Africa)

A Bayesian Approach for the Determination of the Charge Density from Elastic Electron Scattering Data

Presented at MaxEnt97. Appeared in Maximum Entropy and Bayesian Methods, G.J. Erickson, J.T. Rychert and C.R. Smith (Ed.), Kluwer Academic Publishers (http://www.wkap.nl/prod/b/0-7923-5047-2)

physics.data-an

The problem of the determination of the charge density from limited information about the charge form factor is an ill-posed inverse problem. A Bayesian probabilistic approach to this problem which permits to take into account both errors and prior information about the solution is presented. We will show that many classical methods can be considered as special cases of the proposed approach. We address also the problem of the basis function choice for the discretization and the uncertainty of the solution. Some numerical results for an analytical model are presented to show the performance of the proposed method.

physics/0111120

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

A Bayesian Approach to Shape Reconstruction of a Compact Object from a Few Number of Projections

Presented at MaxEnt96. Appeared in Proceedings of the Maximum Entropy Conference, Berg-en-Dal, South Africa, M. Sears, V. Nedeljkovic, N.E. Pendock and S. Sibisi (Ed.), pp 68-77

physics.data-an

Image reconstruction in X ray tomography consists in determining an object from its projections. In many applications such as non destructive testing, we look for an image who has a constant value inside a region (default) and another constant value outside that region (homogeneous region surrounding the default). The image reconstruction problem becomes then the determination of the shape of that region. In this work we model the object (the default region) as a polygonal disc and propose a new method for the estimation of the coordinates of its vertices directly from a very limited number of its projections. Keywords: Computed Imaging, Tomography, Shape reconstruction, Non destructive testing, Regularization, Bayesian estimation, Deformable contours.

physics/0111121

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

New Advances in Bayesian Calculation for Linear and Nonlinear Inverse Problems

Presented at MaxEnt96. Appeared in Proceedings of the Maximum Entropy Conference, Berg-en-Dal, South Africa, M. Sears, V. Nedeljkovic, N.E. Pendock and S. Sibisi (Ed.), pp 92-102

physics.data-an

The Bayesian approach has proved to be a coherent approach to handle ill posed Inverse problems. However, the Bayesian calculations need either an optimization or an integral calculation. The maximum a posteriori (MAP) estimation requires the minimization of a compound criterion which, in general, has two parts: a data fitting part and a prior part. In many situations the criterion to be minimized becomes multimodal. The cost of the Simulated Annealing (SA) based techniques is in general huge for inverse problems. Recently a deterministic optimization technique, based on Graduated Non Convexity (GNC), have been proposed to overcome this difficulty. The objective of this paper is to show two specific implementations of this technique for the following situations: -- Linear inverse problems where the solution is modeled as a piecewise continuous function. The non convexity of the criterion is then due to the special choice of the prior; -- A nonlinear inverse problem which arises in inverse scattering where the non convexity of the criterion is due to the likelihood part. Keywords: Inverse problems, Regularization, Bayesian calculation, Global optimization, Graduated Non Convexity.

physics/0111122

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

A Comparison of Two Approaches: Maximum Entropy on the Mean (MEM) and Bayesian Estimation (BAYES) for Inverse Problems

Presented at MaxEnt96. Appeared in Proceedings of the Maximum Entropy Conference, Berg-en-Dal, South Africa, M. Sears, V. Nedeljkovic, N.E. Pendock and S. Sibisi (Ed.), pp 77-91

physics.data-an

To handle with inverse problems, two probabilistic approaches have been proposed: the maximum entropy on the mean (MEM) and the Bayesian estimation (BAYES). The main object of this presentation is to compare these two approaches which are in fact two different inference procedures to define the solution of an inverse problem as the optimizer of a compound criterion. Keywords: Inverse problems, Maximum Entropy on the Mean, Bayesian inference, Convex analysis.

physics/0111123

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

A full Bayesian approach for inverse problems

Presented at MaxEnt95. Appeared in Maximum Entropy and Bayesian Methods, K. Hanson and R. Silver (Ed.), Kluwer Academic Publishers, pp: 135-144, (http://www.wkap.nl/prod/b/0-7923-4311-5)

physics.data-an

The main object of this paper is to present some general concepts of Bayesian inference and more specifically the estimation of the hyperparameters in inverse problems. We consider a general linear situation where we are given some data $\yb$ related to the unknown parameters $\xb$ by $\yb=\Ab \xb+\nb$ and where we can assign the probability laws $p(\xb|\thetab)$, $p(\yb|\xb,\betab)$, $p(\betab)$ and $p(\thetab)$. The main discussion is then how to infer $\xb$, $\thetab$ and $\betab$ either individually or any combinations of them. Different situations are considered and discussed. As an important example, we consider the case where $\theta$ and $\beta$ are the precision parameters of the Gaussian laws to whom we assign Gamma priors and we propose some new and practical algorithms to estimate them simultaneously. Comparisons and links with other classical methods such as maximum likelihood are presented. Keywords: Bayesian inference, Hyperparameter estimation, Inverse problems, Maximum likelihood.

physics/0111124

Ali Mohammad-Djafari

St\'ephane Brette, Ali Mohammad-Djafari and J\'er\^ome Idier (Laboratoire des Signaux et Syst\`emes (CNRS-ESE-UPS), \'Ecole Sup\'erieure d'\'Electricit\'e, Gif-sur-Yvette, France)

Scale Invariant Markov Models for Bayesian Inversion of Linear Inverse Problems

Presented at MaxEnt95. Appeared in Maximum Entropy and Bayesian Methods, J. Skilling and S. Sibisi (Ed.), Kluwer Academic Publishers, pp: 199-212 (http://www.wkap.nl/prod/b/0-7923-3452-3)

physics.data-an

In a Bayesian approach for solving linear inverse problems one needs to specify the prior laws for calculation of the posterior law. A cost function can also be defined in order to have a common tool for various Bayesian estimators which depend on the data and the hyperparameters. The Gaussian case excepted, these estimators are not linear and so depend on the scale of the measurements. In this paper a weaker property than linearity is imposed on the Bayesian estimator, namely the scale invariance property (SIP).First, we state some results on linear estimation and then we introduce and justify a scale invariance axiom. We show that arbitrary choice of scale measurement can be avoided if the estimator has this SIP. Some examples of classical regularization procedures are shown to be scale invariant. Then we investigate general conditions on classes of Bayesian estimators which satisfy this SIP, as well as their consequences on the cost function and prior laws. We also show that classical methods for hyperparameters estimation (i.e., Maximum Likelihood and Generalized Maximum Likelihood) can be introduced for hyperparameters estimation, and we verify the SIP property for them. Finally we discuss how to choose the prior laws to obtain scale invariant Bayesian estimators. For this, we consider two cases of prior laws: {\em entropic prior laws} and {\em first-order Markov models}. In related preceding works [Mohammad-Djafari90,Mohammad-Djafari93], the SIP constraints have been studied for the case of entropic prior laws. In this paper extension to the case of first-order Markov models is provided. KEYWORDS: Bayesian estimation, Scale invariance, Markov modelling, Inverse Problems, Image reconstruction, Prior model selection

physics/0111125

Ali Mohammad-Djafari

A. Mohammad-Djafari and J\'er\^ome Idier (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

A scale invariant Bayesian method to solve linear inverse problems

Presented at MaxEnt93. Appeared in Maximum Entropy and Bayesian Methods, G. Heidbreder (Ed.), Kluwer Academic Publishers, pp: 121-134, (http://www.wkap.nl/prod/b/0-7923-2851-5)

physics.data-an

In this paper we propose a new Bayesian estimation method to solve linear inverse problems in signal and image restoration and reconstruction problems which has the property to be scale invariant. In general, Bayesian estimators are {\em nonlinear} functions of the observed data. The only exception is the Gaussian case. When dealing with linear inverse problems the linearity is sometimes a too strong property, while {\em scale invariance} often remains a desirable property. As everybody knows one of the main difficulties with using the Bayesian approach in real applications is the assignment of the direct (prior) probability laws before applying the Bayes' rule. We discuss here how to choose prior laws to obtain scale invariant Bayesian estimators. In this paper we discuss and propose a familly of generalized exponential probability distributions functions for the direct probabilities (the prior $p(\xb)$ and the likelihood $p(\yb|\xb)$), for which the posterior $p(\xb|\yb)$, and, consequently, the main posterior estimators are scale invariant. Among many properties, generalized exponential can be considered as the maximum entropy probability distributions subject to the knowledge of a finite set of expectation values of some knwon functions.

physics/0111126

Ali Mohammad-Djafari

A. Mohammad-Djafari (Laboratoire des Signaux et Syst\`emes, CNRS-UPS-SUPELEC, Gif-sur-Yvette, France)

A Matlab Program to Calculate the Maximum Entropy Distributions

Presented at MaxEnt91. Appeared in Maximum Entropy and Bayesian Methods, C.R. Smith, G.J. Erickson and Paul O. Neudorfer (Ed.), pp: 221-234, Kluwer Academic Publishers (http://www.wkap.nl/prod/b/0-7923-2031-X)

physics.data-an

The classical Maximum Entropy (ME) problem consists of determining a probability distribution function (pdf) from a finite set of expectations of known functions. The solution depends on $N+1$ Lagrange multipliers which are determined by solving the set of nonlinear equations formed by the $N$ data constraints and the normalization constraint. In this short communication we give three Matlab programs to calculate these Lagrange multipliers. The first considers the general case where the functions can be any functions. The second considers the special case of power functions $x^n$. In this case the data are the geometrical moments of $p(x)$. The third considers the special case of Fourier series functions $\exp(-j n \omega x)$. In this case the data are the trigonometrical moments of $p(x)$. Some examples are also given to illustrate the usefullness of these programs.

physics/0111127

Benjamin Franksen

B. Franksen (1), R. Bakker (1), B. Kuner (1), J. Rahn (1), H. R\"udiger (1) ((1) BESSY, Berlin, Germany)

A Cost-Efficient PC Based Frame Grabber as Beam Diagnostic Tool in an EPICS Environment

Poster Paper for ICALEPCS-2001 (THAP045), LaTeX, 3 pages, revised version

eConf C011127 (2001) THAP045

physics.ins-det

Analysis of video images is a common way to determine the properties of an electron or synchrotron radiation beam. At BESSY a cost-efficient frame grabber hardware controlled by a Windows PC allows one to perform such an analysis in real-time. Live video images on the PC monitor give operators a direct view of the beam, optionally enhanced by artificial coloring and graphical overlays. The application software has been integrated into the EPICS environment by including a Channel Access (CA) server. Thus the numerical results and the application's control commands are accessible over a network through CA Process Variables. A newly developed C++ class library is used to provide the variables with the usual attributes required by advanced CA clients such as graphical display managers.

physics/0111130

Takemasa Masuda

T. Masuda, T. Fukui, R. Tanaka, A. Yamashita

Data Acquisition System with Shared Memory Network

3 pages, 3 figures, ICALEPCS '01, PSN# THAP046

eConf C011127 (2001) THAP046

physics.acc-ph

The SPring-8 control system provides data acquisition software called Poller/Collector for periodic data taking. Its polling scheme does not support taking data synchronized with an event, and simultaneity in the data from the different VME systems is not guaranteed. Recently, requirement for fast and event-driven data acquisition has increased, and the synchronization of a set of data from the different VME systems is requested. We added new data-taking software to the standard framework with a shared memory network. We designed the software on the VME by updating the original framework that was already used for feedback control. The data filling process on a PC stores sets of the synchronized data on a shared memory board to the database. The shared memory boards provide 250Mbit/s transmission rate and are linked with optical fiber cables. We will install the system to the linac beam position monitors data acquisition as the first application.

physics/0111131

Takemasa Masuda

T. Masuda, T. Ohata, T. Asaka, H. Dewa, T. Fukui, H. Hanaki, N. Hosoda, T. Kobayashi, M. Kodera, A. Mizuno, S. Nakajima, S. Suzuki, M. Takao, R. Tanaka, T. Taniuchi, Y. Taniuchi, H. Tomizawa, A. Yamashita, K. Yanagida

Upgrade of Linac Control System with New Vme Controllers at Spring-8

3 pages, 3 figures, ICALEPCS'01, PSN# WEAT005

eConf C011127 (2001) WEAT005

physics.acc-ph

We integrated an injector linac control system to the SPring-8 standard system on September 2000. As a result of this integration, the SPring-8 accelerator complex was controlled by one unified system. Because the linac was continuously running as the electron beam injector not only for the SPring-8 storage ring but also for New SUBARU, we had to minimize the hardware modification to reduce the time for the development and testing of the new control system. The integration method was almost the same as that of the integration of the booster synchrotron. We report here on the integration of the linac control system with emphasis on the upgrade of the VMEbus controllers and software involving the operating system Solaris 7 as the real-time OS.

physics/0111132

Eivind Almaas

I. Brevik (NTNU), T. A. Sivertsen (NTNU), E. Almaas (OSU)

Radiation forces on an absorbing micrometer-sized sphere in an evanescent field

13 pages, 5 eps figures, accepted for publication in JOSA B

physics.optics cond-mat

The vertical radiation force on an absorbing micrometer-sized dielectric sphere situated in an evanescent field is calculated, using electromagnetic wave theory. The present work is a continuation of an earlier paper [E. Almaas and I. Brevik, J. Opt. Soc. Am. B {\bf 12}, 2429 (1995)], in which both the horizontal and the vertical radiation forces were calculated with the constraint that the sphere was nonabsorbing. Whereas the horizontal force can be well accounted for within this constraint, there is no possibility to describe the {\it repulsiveness} of the vertical force, so distinctly demonstrated in the Kawata-Sugiura experiment [Opt. Lett. {\bf 17}, 772 (1992)], unless a departure from the theory of pure nondispersive dielectrics is made in some way. Introduction of absorption, i.e. a complex refractive index, is one natural way of generalizing the previous theory. We work out general expressions for the vertical force for this case and illustrate the calculations by numerical computations. It turns out that, when applied to the Kawata-Sugiura case, the repulsive radiation force caused by absorption is {\it not} strong enough to account for the actual lifting of the polystyrene latex or glass spheres. The physical reason for the experimental outcome is, in this case, most probably the presence of surfactants making the surface of the spheres partially conducting.

physics/0111133

Masato Ida

Masato Ida

A characteristic frequency of two mutually interacting gas bubbles in an acoustic field

14 pages, 5 figures, elsart, "Eigenfrequency" replaced with "transition frequency" and a reference added, accepted for publication in Phys. Lett. A

Phys. Lett. A 297 (2002) 210-217

10.1016/S0375-9601(02)00422-X

physics.flu-dyn physics.ao-ph physics.gen-ph

Transition frequencies of two spherical gas bubbles interacting in an acoustic field are discussed theoretically. In the present study, transition frequency is defined as the frequency of external sound for which the phase difference between a bubble's pulsation and the external sound is $\pi / 2$. It is shown by a linear theory that a bubble interacting with a neighboring bubble has three (or fewer) transition frequencies but only two natural frequencies. This result means that the bubble has a characteristic frequency besides the natural frequencies.

physics/0111136

Thomas Birke

T. Birke, B. Franksen, R. Lange, P. Laux, R. Mueller (BESSY, Berlin, Germany)

Introducing I/O Channels into the Device Database Opens New Potentialities for Configuration Management

Paper for oral presentation submitted to ICALEPCS'01, San Jose, USA, Nov. 2001, PSN # WEDT003, 1 LaTeX File (3 Pages), 1 EPS-Figure File, 1 LaTeX-Class File, 1 PostScript file, 1 pdf-file

eConf C011127 (2001) WEDT003

physics.acc-ph

The reference RDBMS for BESSY II has been set up with a device oriented data model. This has proven adequate for e.g. template based RTDB generation, modelling etc. But since assigned I/O channels have been stored outside the database (a) numerous specific conditions had to be maintained within the scripts generating configuration files and (b) several generic applications could not be set up automatically by scripts. In a larger re-design effort the I/O channels are introduced into the RDBMS. That modification allows to generate a larger set of RTDBs, map specific conditions into database relations and maintain application configurations by relatively simple extraction scripts.

physics/0111137

Maria Gracheva

M. E. Gracheva and J. D. Gunton

Intercellular Communication Via Intracellular Calcium Oscillations

11 pages, 4 figures

physics.bio-ph q-bio

In this letter we present the results of a simple model for intercellular communication via calcium oscillations, motivated in part by a recent experimental study. The model describes two cells (a "donor" and "sensor") whose intracellular dynamics involve a calcium-induced, calcium release process. The cells are coupled by assuming that the the input of the sensor cell is proportional to the output of the donor cell. As one varies the frequency of calcium oscillations of the donor cell, the sensor cell passes through a sequence of N:M phase locked regimes and exhibits a "Devil's staircase" behavior. Such a phase locked response has been seen experimentally in pulsatile stimulation of single cells. We also study a stochastic version of the coupled two cell model. We find that phase locking holds for realistic choices for the cell volume.

physics/0111138

Masato Ida

Masato Ida

Investigation of transition frequencies of two acoustically coupled bubbles using a direct numerical simulation technique

18 pages, 8 figures, in press

J. Phys. Soc. Jpn. 73 (2004), pp.3026-3033

10.1143/JPSJ.73.3026

physics.flu-dyn math.NA physics.comp-ph

The theoretical results regarding the ``transition frequencies'' of two acoustically interacting bubbles have been verified numerically. The theory provided by Ida [Phys. Lett. A 297 (2002) 210] predicted the existence of three transition frequencies per bubble, each of which has the phase difference of $\pi /2$ between a bubble's pulsation and the external sound field, while previous theories predicted only two natural frequencies which cause such phase shifts. Namely, two of the three transition frequencies correspond to the natural frequencies, while the remaining does not. In a subsequent paper [M. Ida, Phys. Rev. E 67 (2003) 056617], it was shown theoretically that transition frequencies other than the natural frequencies may cause the sign reversal of the secondary Bjerknes force acting between pulsating bubbles. In the present study, we employ a direct numerical simulation technique that uses the compressible Navier-Stokes equations with a surface-tension term as the governing equations to investigate the transition frequencies of two coupled bubbles by observing their pulsation amplitudes and directions of translational motion, both of which change as the driving frequency changes. The numerical results reproduce the recent theoretical predictions, validating the existence of the transition frequencies not corresponding to the natural frequency.

physics/0111145

Wolfgang Baumjohann

W. Baumjohann and R. Nakamura (Space Research Institute Graz, Austria)

Updating the Near-Earth Neutral Line Model

physics.space-ph

In the past thirty years the Near-Earth Neutral Line model for substorms has been proven to be correct in its basic assumption, i.e., that a new neutral line is created near the Earth during substorm onset. Yet there have also been numerous changes and additions to this model, which were necessary to give a more complete and deeper understanding of the substorm process. This process is still continuing.

physics/0111146

Robert C. Sass

T. Lahey, J. Rock, R. Sass, H. Shoaee, K. Underwood

An Integrated Enterprise Accelerator Database for the SLC Control System

eConf C011127 (2001) WEAP072

physics.acc-ph

Since its inception in the early 1980's, the SLC control system has been driven by a highly structured memory resident real-time database. While efficient, its rigid structure and file-based sources makes it difficult to maintain and extract relevant information. The goal of transforming the sources for this database into a relational form is to enable it to be part of a Control System Enterprise Database that is an integrated central repository for SLC accelerator device and control system data with links to other associated databases.

physics/0111148

Sergey. E. Karnaev

D. Filimonov, S. Karnaev, B. Levichev, S. Smirnov, A.Veklov (Budker Institute of Nuclear Physics, Novosibirsk, Russia)

Database and Channel Access on the VEPP-4

3 pages, 5 figures, ICALEPCS'01, PSN#WEAP029

eConf C011127 (2001) WEAP029

physics.acc-ph

The VEPP-4 control system was designed almost 20 years ago as CAMAC-based distributed control system. Today the main peculiarity of the upgraded VEPP-4 control system is the employment of obsolete CAMAC-embedded 24-bit Odrenok computers in the middle (process) level. The communication software is developed to provide an effective interaction between user (operator) applications on the high level and executive programs in the middle level. The communication software is Linux-based and includes the Application Server and Device Servers. The Application Server provides channel and database access for user applications. The Device Servers provide interaction with the hardware. The backend database server is based on PostgreSQL. This paper describes the structure of the VEPP-4 control system database and data/channel access procedures.

physics/0111154

John C. L. Brazier

J.C.L. Brazier, A. Dinius, P. Semanaz

Evolution of the SPS Power Converter Controls towards the LHC Era

Paper is 3 pages for ICAPEPCS 01 27 - 30 November 2001 San Jose. John C L Brazier is the principal author and a consultant to CERN (hence the CERN Email address but UK Organisation)

eConf C011127 (2001) WEAP017

physics.acc-ph

By the end of the nineties, the power converter control system (Mugef) of the CERN proton accelerator (SPS) had undergone a complete modernization. This resulted in newly developed hardware for function generation, measurement and I/O in a VME environment, under the LynxOS real-time operating system. This has provided a platform on which extensions can be developed for future operation in the Large Hadron Collider (LHC) era. This paper describes some of these extensions, in particular a fast Surveillance and Interlock system for monitoring the power converter output currents. This will be mandatory for the safe operation of the SPS transfer lines TI2 & TI8 to LHC and for similar applications in the future. The strategies employed to cope with various failure modes of the power converters and the timely activation of the interlock are outlined. The new SPS controls infrastructure now under development, will give rise to new modes of operation for the Mugef systems. Integration with the proposed middleware must be undertaken in a structured evolution, while retaining compatibility with the current usage.

physics/0111155

Richard S. Abbott

R. Abbott, P. King

Control System Design for the LIGO Pre-stabilized Laser

3 Pages, 3 figures, ICALEPCS Conference

eConf C011127 (2001) WEAP038

physics.ins-det

To meet the strain sensitivity requirements [1], [2] of the Laser Interferometer Gravitational Wave Observatory (LIGO), the laser frequency and amplitude noise must initially be reduced by a factor of 1000 in the pre-stabilized portion of the interferometer [3]. A control system was implemented to provide laser noise suppression, data acquisition interfaces, diagnostics, and operator control inputs. This paper describes the VME-based analog and digital controls used in the LIGO Pre-stabilized Laser (PSL).

physics/0111156

Smolyakov

A. I. Smolyakov, M. Yagi, Y. Kishimoto

Kinetic temperature gradient driven modes in inhomogeneous plasmas

10 pages, 5 figures, submitted to Physical Review Letters

physics.plasm-ph

New unstable temperature gradient driven modes in an inhomogeneous plasma are identified. These modes represent transient $\omega \simeq k_{\Vert }v_{th}^{(e,i)}$ sound oscillations in magnetized plasma that are kinetically destabilized via Landau interactions. Electron and ion sound branches are unstable for large values of the Larmor radius parameter $% k_{\bot}\rho _{e,i}\gg 1,$ respectively. The instability occurs due to a specific plasma response that significantly deviates from Boltzmann distribution in the region $k_{\bot}\rho_{i,e}\gg 1$ . Pacs: 52.35 Kt, 52.35 Qz

physics/0111158

C. M. Chu

C.M. Chu (1), J. Galambos (1), J. Wei (1 and 2), C.K. Allen (3), P. McGehee (3) ((1) Ornl, (2) BNL, (3) Lanl)

SNS Application Programming Plan

3 pages, 3 Postscript figures, for ICALEPCS 2001, San Jose, CA, November, 2001

eConf C011127 (2001) THAP060

THAP060

physics.acc-ph

The architecture for Spallation Neutron Source accelerator physics application programs is presented. These high level applications involve processing and managing information from the diagnostic instruments, the machine control system, models and static databases; they will be used to investigate and control beam behavior. Primary components include an SNS global database and Java-based Application Toolkit, called XAL. A key element in the SNS application programs is time synchronization of data used in these applications, due to the short pulse length (1 ms), pulsed (60 Hz) nature of the device. The data synchronization progress is also presented.

physics/0111159

Jonathan S. Laster

J.S. Laster, T. Clifford, T. D'Ottavio, A. Marusic, J.F. Skelly

Post Mortem System - Playback of the RHIC Collider

Poster paper for ICALEPCS 2001 conference, San Jose, USA, (THAP063), 3 pages in PDF format

eConf C011127 (2001) THAP063

physics.acc-ph

A Post Mortem System was developed for the Relativistic Heavy Ion Collider at Brookhaven National Laboratory to provide a playback of the collider state at the time of a beam abort, quench, or other failure event. Post Mortem data is used to provide diagnostics about the failure and to improve future stores. This data is read from hardware buffers and is written directly to the main file system by Accelerator Device Objects in the front-end computers. The Post Mortem System has facilitated analysis of loss monitor and power supply data, such as beam loss during magnet quenches, dump kicker misfires and power supply malfunctions. System details and recent operating experience will be discussed.

physics/0111161

Greg White

G. R. White, H. Shoaee

The NLC Software Requirements Methodology

Contributed paper at International Conference on Accelerator and Large Experimental Physics Control Systems - ICALEPCS 2001, San Jose, USA, November 2001 (TUAP042)

eConf C011127 (2001) TUAP042

physics.acc-ph

We describe the software requirements and development methodology developed for the NLC control system. Given the longevity of that project, and the likely geographical distribution of the collaborating engineers, the planned requirements management process is somewhat more formal than the norm in high energy physics projects. The short term goals of the requirements process are to accurately estimate costs, to decompose the problem, and to determine likely technologies. The long term goal is to enable a smooth transition from high level functional requirements to specific subsystem and component requirements for individual programmers, and to support distributed development. The methodology covers both ends of that life cycle. It covers both the analytical and documentary tools for software engineering, and project management support.

physics/0111162

John T. Morris

J. Morris, T. D'Ottavio (Brookhaven National Laboratory)

Status Report for the RHIC Control System*

submitted to ICALEPCS 2001, 3 pages, no figures, {*} Work supported by US Department of Energy

eConf C011127 (2001) TUAT002

physics.acc-ph

The Relativistic Heavy Ion Collider (RHIC) at Brookhaven has completed nearly two years of successful commissioning and operation. The control system is briefly reviewed and its contribution to the RHIC effort is analyzed, with emphasis on special challenges and innovative design: continuing efforts are also discussed.

physics/0111163

John T. Morris

J. T. Morris, T.S. Clifford, B. Frak, J. Laster, A. Marusic, J. van Zeijts (Brookhaven National Laboratory)

RHIC Power Supply Ramp Diagnostics*

submitted to ICALEPCS 2001, 3 pages, 1 figure, {*} Work supported by US Department of Energy

eConf C011127 (2001) WEAP039

physics.acc-ph

Reliable and reproducible performance of the more than 800 Relativistic Heavy Ion Collider (RHIC) magnet power supplies is essential to successful RHIC operation. In order to support power supply commissioning, a system was developed to capture detailed power supply measurements from all the RHIC ring power supplies during acceleration ramps. Diagnostic tools were developed to allow experts to assess ramp reproducibility and rapidly identify problems. The system has now become a routine part of RHIC operations, with data captured for every acceleration ramp. This paper describes the RHIC power supply ramp diagnostic system and considers its impact on RHIC operations.

physics/0111165

Angom Dilip Singh

Angom Dilip Singh, Bhanu Pratap Das and Debashis Mukherjee

Coupled Electron Pair Approximation Calculation of the Electric Dipole Moment of Atomic Yb

19 pages, 13 figures

physics.atom-ph

The existence of a finite electric dipole moment (EDM) d_a of the closed-shell atom Yb implies parity and time reversal violations involving the nuclear sector. An important effect which can contribute to the Yb EDM is the tensor-pseudotensor electron-nucleus interaction characterized by the coupling constant C_T. Within the Standard Model (SM) of particle physics C_T=0, as this form of interaction is not allowed. If a finite d_a of Yb is observed in experiments, then an estimate of C_T can be obtained by combining with the theoretical calculations. A non-zero C_T implies physics beyond the standard model. In this paper we present the result of our ab initio calculation of the EDM Yb using different many-body methods.

physics/0111166

Franck Di Maio

V. Baggiolini, S. Jensen, K. Kostro, F. Di Maio, A. Risso, N. Trofimov

Remote Device Access in the New CERN Accelerator Controls Middleware

Presented at ICALEPCS 2002, November 27-30, 2001, San Jose, CA (THAP003)

eConf C011127 (2001) THAP003

physics.acc-ph

This paper presents the Remote Device Access (RDA) package developed at CERN in the framework of the joint PS/SL Controls Middleware project. The package design reflects the Accelerator Device Model in which devices, named entities in the control system, can be controlled via properties. RDA implements this model in a distributed environment with devices residing in servers that can run anywhere in the controls network. It provides a location-independent and reliable access to the devices from control programs. By invoking the device access methods, clients can read, write and subscribe to device property values. We describe the architecture and design of RDA, its API, and CORBA-based implementations in Java and C++. First applications of RDA in the CERN accelerator control systems are described as well.

physics/0111168

Jingyi Li

Jingyi Li, Gongfa Liu, Weimin Li, Chuan Li, Kaihong Li, Caozheng Diao, Zuping Liu

Ramping Control of HLS Storage Ring

2 pages, ICALEPCS'01 conference

eConf C011127 (2001) THAP064

physics.acc-ph

HLS (Hefei Light Source) is a second generation synchrotron radiation source. After injected into the storage ring at energy of 200MeV, the electrons will be ramped to 800MeV. During ramping, the magnetic fields of the bend, quadruple and sextuple magnets are ramped up synchronously to keep the working point of the storage ring unchanged. This process is carefully controlled by HLS control system, which is built under EPICS. Several measures are taken to insure the synchronization and linearity of the ramping.

physics/0111169

Gongfa Liu

Gongfa Liu, Jingyi Li, Weimin Li, Chuan Li, Kaihong Li, Lei Shang

Injection Control System of HLS Storage Ring

2pages, 2 figures, ICALEPCS2001, PSN TUAP061

physics.acc-ph

The injection control system of Hefei Light Source (HLS) storage ring is a subsystem of the upgraded HLS control system, which is based upon EPICS. Three programmable logic controllers (PLCs) are used as device controllers, which control one septum modulator and four kicker modulators of HLS storage ring. An Industrial PC is used as Input/Output Controller (IOC) and it connects the PLCs with serial communication (RS232 mode) over fibre. A PC with Linux is used as operator interface (OPI), operator application are running on it. The control system was completed in July 2000. The commissioning shows that the control system is reliable and easy operational.

physics/0111172

Juraj Krempasky

J. Krempasky, R. Krempaska, D. Vermeulen, D. Maden, T. Korhonnen, W. Portmann, S. Hunt, R. Abela, M. Muntwiler

The SLS Beamlines Data Acquisition and Control System

5 pages, 4 figures

eConf C011127 (2001) TUBT002

physics.acc-ph

On December 15th the Swiss Light Source (SLS) produced a stored beam for the first time. This important milestone was achieved in a very tight time schedule. The fact that all major systems are controlled by Epics made this challenge feasible. In the first phase there are four beamlines: two for the surface science community, one for powder and surface diffraction and computed micro-tomography, and the last one for protein crystallography. All of them are equipped with insertion devices, which users want to treat as active sub-systems like a monochromator or experimental station. The beamline control systems are based on the same hardware and software technology as is the machine. This implies extensive use of Personal Computers running Linux RedHat 6.2 and VME systems (PowerPC). The advantage of this choice is a staightforward implementation of the insertion devices into the beamline and experiment framework. Although the experiment Application Program Interfaces differ from beamline to beamline, the standard software technology for linking all sub-systems is based on the Epics toolkit and Cdev. The diagnostic tools provided by this toolkit are being extensively used during the beamline commissioning. Finallly we account on some examples of integrating dedicated 3rd party and commercial non Epics software products for experiment control into the beamline control system. Key elements in this domain are CORBA, Python and Portable Channel Access Server.

physics/0111173

Timo T. Korhonen

Timo Korhonen, Martin Heiniger

Timing system of the Swiss Light Source

Presented at ICALEPCS 2002, November 27-30, 2001, San Jose, CA (FRAT004). 3 pages, 1 figure

eConf C011127 (2001) FRAT004

physics.acc-ph

The timing system of the Swiss Light Source is based on the event system concept of APS, Argonne [1]. However, for SLS the hardware was completely redesigned while preserving the software compatibility with the APS system. This gave us a head start in the implementation: we could use the latest available hardware and take advantage of the features integrated in the EPICS software. The event system is used as the sole timing distribution method, for hardware trigger delivery (assisted with a high-precision delay at a few places) and for controlling all the timing-related tasks of operation: injector sequencing, filling patterns, software synchronization, timestamps and so on. The event network is also extended to the beamlines to allow synchronization of the beamline experiments. The implementation consists of the hardware (Gigabit Ethernet link, FPGAs) and a firmware core written in VHDL. The functionality of the cards can be modified in situ by rewriting the firmware in flash memory. On the other hand, the functionality can be easily ported to new hardware architectures, allowing smooth upgrade paths and maximal reusability of the soft- and hardware resources. [1] F.R.Lenkszus et.al., 'The Advanced Photon Source Event System', Proc. ICALEPCS'95

physics/0111174

Roland Mueller

R. Bakker, T. Birke, R. Mueller (BESSY, Berlin, Germany)

Signal Archiving and Retrieval: Essential Long Term Performance Tuning Tool

Paper for oral presentation submitted to ICALEPCS'01, San Jose, USA, Nov.2001, PSN # FRBT005, 1 LaTeX File (3 Pages), 5 EPS-Figure Files, 1 LaTeX-Class File, 1 PostScript File, 1 pdf-File

eConf C011127 (2001) FRBT005

physics.acc-ph

The first two years of user service of the third generation light source BESSY II emphasized the importance of a reliable, comprehensive and dense logging of a few thousand setpoints, readbacks, status and alarm values. Today data from sources with various characteristics residing in different protected networks are centrally collected and retrievable via an uncomplex CGI program to any desktop system on the site. Data post-processing tools cover Windows applications, IDL, SDDS and custom programs matching users skills and preferences. In this paper illustrative sample data explorations are described that underline the importance of the logging system for operations as well as for the understanding of singular events or long term drifts. Serious shortcomings of the present installation and focus of further development are described.

physics/0111176

V.V. Lyahov, V.M. Neshchadim

The Landau Damping Effect and Complex-valued Nature of Physical Quantities

6 pages, 1 table

Glushcko's Physical & Engineering Laboratory report N-099/20.11.2001

physics.plasm-ph

Within the framework of the hypothesis offered by authors about complex-valued nature of physical quantities, the effect of the Landau damping has been explored with assumption that not only frequency can be a small imaginary component but also a wave vector. The numerical solution of the obtained dispersion equation testifies that uncollisional damping is accompanied in a certain region of space by antidumping of waves, and in particular situations antidumping may prevail over damping. It is possible that this effect may explain the experimental difficulties connected with inhibition of instabilities of plasma in the problem of controllable thermonuclear fusion.

physics/0111179

Bob Bryant

R. M. Bryant, R. W. Carey, R. V. Claybourn, G. Pavel, W. J. Schaefer

National Ignition Facility (NIF) Control Network Design and Analysis

3 pages, 2 figures, ICALEPCS 2001

eConf C011127 (2001) THDT004

THDT004

physics.ins-det

This paper describes the requirements, design, and analysis of the control network for the National Ignition Facility (NIF). The network uses Ethernet technology throughout and ATM is used for efficient digital video transport.

physics/0111181

Kazuro Furukawa

K. Furukawa, J. Chiba, N. Kamikubota, H. Nakagawa

Implementation of the Epics Device Support for Network-Based Controllers

LaTeX, 3 pages, 2 figures, ICALEPCS2001, TUAP066, http://www-linac.kek.jp/linac-paper/

eConf C011127 (2001) TUAP066

physics.acc-ph

In the control system of the JAERI-KEK joint project (High Intensity Proton Accelerator Facility), it is planned to employ network-based controllers such as PLC's and measurement stations instead of using other field control networks, since the network hardware and software can be standardized and they have been successfully utilized in other accelerator control systems in KEK. EPICS software support for those controllers was designed paying special attention to robustness and has been implemented and applied for the accelerator test stand. Basic functionalities were confirmed and miscellaneous functions such as diagnosis of the software itself would be added. Since many kinds of network-based equipment such as oscilloscopes have become available recently, they are considered to be integrated as well. They may enable more manageable controllers.